Exclusive Features of RMS Mills 

All RMS Machines are Built in the United States

Roll Alignment System


Adjusting Particle Size:
 All adjustments are located conveniently on the front of the machine; allowing for easy and accurate adjustment of the particle size. This patented innovation allows precision roll alignment in seconds, while eliminating the need to remove covers and belt guards.

Roller mill
 Roller Mill

Dual spring protection allows any foreign material to pass through the rolls without damaging the machine. This assembly is a bolt on component, which can be easily replaced; which allows you to bring the machine back to new machine tolerances.


Each fine adjustment assembly contains machined parts that are closely tolerance to fit together exactly. These close tolerances hold the roll exactly where the operator places it and remains there for a consistent grind 24 hours a day, seven days a week.(Left) This dial displays the position of each roll in the machine. Each hatch moves the roll one thousandth of inch, giving the operator extremely accurate adjustment.

The Roll Grinding Drive




Roller Mill    roller
mill         

← The photo to the left shows one side of a Patented RMS dual motor drive system that uses only “Super HC VX” belts. This superior drive system solves many of the all too common problems associated with conventional double sided belt drives::

  • Eliminates all belt slippage: Conventional double sided belt drives slip, stretch, generate excessive heat, and have a lower service factor than RMS VX drives. Therefore, maintenance issues and cost are much more frequent.
  • Eliminating all idlers RMS drives do not have any idler pulleys. Our three point drive does not need any idlers or tentioners.  This eliminates moving components and makes the drive system simpler.
  • Allows for shorter roll shafts: Double sided belts are not rated for as much horse power as a VX belt; thus more belts and longer shafts are required. With our patented drive we have decreased the number of belts at least by half.

Simplicity of Design...means reliability of operation!

This photo shows one side of a Patented RMS DUAL Motor (150HP) Drive System. This RMS 12 x 52" mill is driven by two 75 horsepower motors. As you can see, the machine's design is self-explanatory and very manageable

  • Our first priority was making roll changes as easy and convenient as possible, reducing cost and minimizing downtime
  • Cost studies have shown a 35% decrease in service costs over our competitors
drive.JPG (108941 bytes)
 
Belt Guard Covers

Roller Mill

Are also "quick release"
  • Front and back covers are secured with wing nuts to allow roll inspection without the need of any tools
roller mill
Grease Bank
  • ( on the right) Grease Banks for quick maintenance.
  • Off the shelf parts available locally.
  • Feed roll option will prevent plug ups in power outages.
  • We carry all replacement parts, which are available for overnight shipping.



Feed Roll
Our Automated Feed roll optimizes the performance of your roller grinder or roller mill. The software included will monitor grinder load and control fee rate at peak efficiency. Inputs are preprogrammed to monitor ground product destination and automatically grind product to fill bins.
  • A large diameter solid cast iron feed roll is standard equipment on the RMS Industrial Series Roller-Grinder
  • The feed roll can be slowed to a complete stop, thus shutting off the flow of grain to the mill for end of the day shutdown



Roller Mill
 

Automated Feeder Option

Remote feed 2 .JPG (41515 bytes)
 




     Remote Feed 1 .JPG (15444 bytes)
  
Remote Control Feed Roll System Includes:
 Standard on all 12" diameter Industrial mills
  • Our exclusive micro-computer controlled overload shutdown system, which continually and automatically maintains full motor load regardless of the desired grind or the grain condition such as test weight or moisture.
  • In the event of an over amperage condition the system will continue to slow down the feed roll until the amperage is once again at the preset value (full motor load).
  • In a plug up situation in which the over amperage condition cannot be corrected, the system will completely stop the feed roll and sound an alarm. A pre-wired control panel is included.
(Nema 12 dust-tight enclosure)
Click here to find out more about Automation

 
Sample ports and Dust Problems

 All RMS machines are guaranteed to be dust tight

Roller Mill Dust free sample ports are standard on our equipment.

  • A felt lined spring loaded trap door on the inside of the mill automatically closes to insure a dust free seal.
  •  Convenient sampling helps you maintain the highest quality grind and consistent feed. Purchase one of test kits for an on the spot indication of your average particle size, or send a sample to our testing facility for a detailed analysis.
Quality Design:
  • 2D and 3D design capabilities.
  • Custom projects are always welcome.
  • Fully equipped test facility with the ability to test any product you would like.
  • Robust design.
  • 1/2'' thick frame on 9'' machines and 5/8''thick on 12'' machines.
  • Made in the USA.

 Roller Mill

Click here to view mill dimensions
To Find out more about the products or services offered by RMS Roller-Grinder
  Click here to contact us
 

 
Home
New Mills
Mill Features
Service
Roll Sharpening
Accessories
Rebuilt Mills
What's New!
Links
Contact Us
Directions
FAQ
Home     New Mills     Mill Features     Service     Roll Sharpening     Accessories     Rebuilt Mills     What's New!     Links     Contact Us     Directions     FAQ

RMS Roller Grinder  •  27116 Grummand Ave.  •  Tea, SD  57039  •  Phone: 605-368-9007  •  rms@rmsroller-grinder.com
 
This site contains information on RMS Roller Grinder, RMS Roller Grinder South Dakota, RMS South Dakota, RMS Roll, RMS Roller South Dakota, Roskamp Champion, Roskamp Champion Iowa, Roskamp Champion Iowa, Roscamp, Ross kamp, Champion, CPM Iowa, Roskamp Champion united states, Scherre South Dakota, Schear, Schere, Henke, buffalo, buffalo mill supply, buffalo Kansas, Bliss, ferrel ross, ferrell ross, ferrell ross texas, ferrell-ross, ferell ross, Ferrell Ross, Automatic Ag, Automatic, IFA, IFA Iowa, Lonestar, Lone Star, Lone Star South Dakota, Roll Sharpening, Roller Sharpening, Fluting, Roll Fluting, Roller mill, Roller Mills, Roll mill, flaking mills, Grain processing, Roll, Grind, grinding, Grinder, Feedmill, Feed mill, feed mill south Dakota, feed mill Iowa, feed mill Minnesota, feed mill Nebraska, feed mill Wisconsin, feed mill texas, feed mill Kansas, Corn, Grain, Davis, Mill Service, Mill Sales, Millwright, Millwright Services, Particle reduction, Feedlot, Feed lot, feed lot south Dakota, feed lot Nebraska, feed lot Minnesota, feed lot Iowa, feed lot Kansas, feed lot Wisconsin, feed lot Illinois, Agriculture Equipment, Agriculture Machines, Feed, Process, Equipment, feed industry, deviation, micron, hogs, hog feed, livestock, swine, cattle feed, poultry, beef, pork, turkey, cattle, Rolling, Chicken feed, Turkey feed, Poultry feed, Portable Mill, portable roller mill, electric mills, trailer mills, Crack, Flake, Magnet, Oats, Barley, Wheat, Milo, Crimping, Mill Service, Feed clean, Feed cleaner, scalper, magnet system, scalper system, clipper, Mill Contractor, Feed Mill Contractor, feed mill builder, feed mill builder iowa, feed mill builder south Dakota, feed mill builder Minnesota, feed mill builder Nebraska, feed mill contractor south Dakota, feed mill contractor Minnesota, feed mill contractor iowa, feed mill contractor Nebraska, Blue Ox, Denver, South Dakota, Minnesota, Wisconsin, Iowa, Nebraska, Kansas, Oklahoma, Texas, North Carolina, North Dakota, Illinois, Ohio, Indiana, Canada, Alberta, Saskatchewan, Ontario.